dcsimg

Sara

Forum Replies Created

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • #751627

    The dust particles of concrete are very fine, and vacuuming will not remove them easily. Especially when you drill the hole for tapcon screws.
    I’m suggesting a different tip. We use it all the time and got the best results.
    Use a liquid to remove all of the dust particles. Just mix 12 ounces of hydrogen peroxide in 1 gallon of water and use soft cotton rags to wipe the surfaces of the drill chuck.
    Water alone doesn’t pick up all of such dust particles and requires multiple sorts of cleanings.
    This solution eliminates the particles and makes it a bit easier for the rags to absorb them and carry them away.

    #749930

    You need to get a new power supply that will increase the voltage from 110V to 220V so that machine will work, otherwise it will not work because of low voltage.
    Plug is not the issue here because you will get the convertible adopter anywhere on ebay or amazon

    #749929

    It looks like the block is missing from the place, put concrete in it and page it.
    Do not forget to put a bonding agent before putting concrete,

    #749521

    This is How you cn keep your tools clean to increase the durability and life:

    Step 1 – Scrape and soak: Tools

    Step 2 – Dump and refill: Dump Dirty Water and Fill the Bucket with Clean Warm Water.

    Step 3 – Scrub: Use Scrubbing Brush to Wash the Tools.

    Step 4 – Rinse and dry: Tools

    Step 5 – Apply rust inhibitor: Like WD40

    Bingo… You are good to go now.

    #749495

    I have installed once with my dad, took a half day and hell a lot of energy. If you have the tools and power you can do it. Just make sure to get the right parts at the right place using the cabinet installing manual.

    #749064

    I think resurfacing will do the job.

    #749061

    Why dont you re do the whole floor and this time let the professional handle the business. and you will never have to worry again.

    #748634

    Wedge anchors are one of the most commonly used concrete anchors in our daily lives. Most concrete anchors work in one of two ways–either by expanding against the sides of the hole and gripping the concrete or by the friction against the sides of the hole. The gripping power of an anchor depends on the quality of the concrete and where the anchor is positioned. If the concrete is old and brittle, the holding power of the fastener will be reduced.
    These are the fasteners you’ll buy and use most often in your houses. They’re great for fastening the shelf brackets, rake, towel bars, and any sort of brackets, shower doors, pipe and conduit retainers or anything else lighter than 50 lbs. They need a pilot hole at least as deep as the screw will penetrate. Each package will tell the size of the hole and screw that’ll work best.

    #748546

    Moisture creates bubbles and the paint starts to peel off. It might be the moisture issue but it is not a serious one because the paint is still intact and bubble is still under the paint. You should peel off the paint your self and check what is the problem with the planks.
    You are saying that the house is very old, it might start getting moisture from somewhere.

    #748485

    I think it is good.

    #747741

    no idea,
    but you can always use it where you want because now you have it.

    #747378

    I think you should get the leak fixed before it can do any more damage. The thing is that if the water is getting under, it will create more problems to the flooring.
    Boschmanbrian is right, you can tag a guy who has more experience in this area.

    #747342

    This is the Most Frustrating Thing for me..

    Attachments:
    #747299

    Installing Tapcon Concrete Screws can be done in few easy steps and can be used when working with electrical boxes, wood headers, and other exterior insulation systems. Tapcons are best matched for light to medium duty fastening purposes, are available in standard 3/16” and 1/4” diameters, as well as large diameter size varieties of 3/8”, 1/2″, 5/8” and 3/4” and, are offered in an extensive variety of materials (including the stainless steel) to meet every construction need. After installation, they can be removed and replaced without disturbing the base material.
    1. Select an appropriate size of a masonry screw.
    2. Choose a drill bit. Place drill bit and screw together. Use Tape to wrap at a point equal to the size of a size, so that you may not drill a deeper than the actual size of a screw.
    3. Drill a hole into the base material.
    4. Clean out the hole of all the debris.
    5. Insert pointed end of masonry screw into the base material and drive slowly with a slight push force so that threads are fixed into the base material.

Viewing 14 posts - 1 through 14 (of 14 total)
© Robert Bosch Tool Corporation 2014, all rights reserved.
queries. 0.649 seconds