dcsimg

V6…Today I used my Bosch…

This topic contains 1,007 replies, has 38 voices, and was last updated by  RonW 3 months, 3 weeks ago.

Viewing 20 posts - 21 through 40 (of 1,008 total)
  • Author
    Posts
  • #594955

    Today i used my gll2-45 laser level idh181 bosch pb360 radio thats about it most of the day was painting

    #595725

    V6 already. Those Bosch tools are keeping busy. Thanks for the new version Andrew.

    My You Tube channel: https://www.youtube.com/channel/UCA5AretE3xPoVDV61AxUdUA

    I don't do a fast job. I don't do a slow job. I do a half fast job.

    #595732

    Austin
    Pro
    Covington, KY

    On the 12“ glider for a good part of the day as I precut lots of casing

    #595740

    Doobie
    Pro
    Ajax, ON

    Used my PB360 outside today in the cold while shovelling a LOT of dirt.

    Kevin.

    #595758

    Today i used my cm10gd miter saw vac090s vacuum gll2-45 crossline laser cet3-10 air compressor 16 and 18 gauge nailers and mxh180 omt tool

    #595765

    kurt@welkerhomes.com
    Pro
    Owatonna, MN - Minnesota

    Used my new sander and my 18ga nail gun. I really like the feel of the nail gun but it does not seem to want to set the brads even with the depth of drive set at max. I may have to try it with a different compressor and a little higher pressure.

    #595891

    I used both of my FL12’s last night to take down a few bins from the garage attic. I haven’t hooked up the electric in there after I finished up the ceiling with drywall.
    I attached some nail stop plates to the rafters. works great with the magnet from the FL12

    "If you're going to do something, do it right the first time"
    -----------------------------------------------------------------------
    Instagram
    -----------------------------------------------------------------------
    Palm Springs, CA

    #595961

    I used my GCM12SD (12″ glide) today to build more shelving units.
    PB360 was running in the back

    Attachments:

    "If you're going to do something, do it right the first time"
    -----------------------------------------------------------------------
    Instagram
    -----------------------------------------------------------------------
    Palm Springs, CA

    #595964

    Today i used my cm10gd miter saw gts1031 table saw cet3-10 air compressor 16 and 18 gauge nailers mxh180 omt pr20 router

    #596000

    DirtyWhiteBoy
    Pro
    Honolulu,, Hi.

    Today I was using the Bosch carbide multi tool blade to under cut drywall and corain sills.

    Dirty

    A Working Pro since 1988!

    Member since January 26, 2013.

    #596057

    Today I was using the Bosch carbide multi tool blade to under cut drywall and corain sills.

    I still like that idea of using corian for the sills. I use it to make nuts for guitars.

    My You Tube channel: https://www.youtube.com/channel/UCA5AretE3xPoVDV61AxUdUA

    I don't do a fast job. I don't do a slow job. I do a half fast job.

    #596175

    cmeyer25
    Pro
    Bellingham, WA

    That’s quite the view @madman_us!

    Today I used my MR23 and a flush trim bit to smooth out both sides of a combination teeter-totter/ bridge I’m making for a friend who has a one year old. Both sides are all evened out now, so I’ll be moving on to making the steps tomorrow – I ripped them to width on my gts1031 this morning in prep for tomorrow.

    Attachments:

    Charlie
    __________________

    Instagram

    #596196

    r-ice
    Pro
    Durham region, ON

    I used my GCM12SD (12″ glide) today to build more shelving units.
    PB360 was running in the back

    Im envious of the view you have, what I would give to have that here in Toronto lol.

    I just used the fl12 today in the truck, as I was up north without any lights.

    #596199

    smallerstick
    Pro
    Listowel, ON

    I used my 1619 router in the table today and the Glide, of course. The Glide gets used almost every day now in my shop.

    If the women don't find you handsome, they should at least find you handy. -- Red Green

    #596268

    GCM12SD (12″ glide), IDH182 (impactor), DDS181 (drill), PB360
    in the garage/shop for my shelf project

    "If you're going to do something, do it right the first time"
    -----------------------------------------------------------------------
    Instagram
    -----------------------------------------------------------------------
    Palm Springs, CA

    #596290

    Today i did more trim used my cm10gd mitersaw gts1031 tablr saw cet3-10 air compressor 18 and 16 gauge bosch nailers pb360 radio was on all day used the mxh180 omt tool. And used the vac090s vacuum

    #596305

    DirtyWhiteBoy
    Pro
    Honolulu,, Hi.

    Today I had tons of drywall to cut with the Bosch carbide multi tool blade.

    Dirty

    A Working Pro since 1988!

    Member since January 26, 2013.

    #596357

    RonW
    Pro
    Holladay, Tn

    Got my heated jacket out for the first time this morning. Sure feels good.

    Ron

    A Working Pro since 1994!

    Member since March 26, 2014.

    #596385

    58Chev
    Pro
    Etobicoke, ON

    Cutting up some ply on my 4100-09 table saw. Been trying with the idea of making an air cleaner.

    “If you don’t pass on the knowledge you have to others, it Dies with you”
    — Glenn Botting

    #596387

    Boschmanbrian
    Pro
    Montreal , QC, Canada

    Just used the FL12 and the 12 volt vac
    Cleaning something up in the garage.

Viewing 20 posts - 21 through 40 (of 1,008 total)

The topic ‘V6…Today I used my Bosch…’ is closed to new replies.

queries. 3.417 seconds