dcsimg

a compilation of the best jobs ite safety practices.

Viewing 20 posts - 1 through 20 (of 57 total)
  • Author
    Posts
  • #162747
    kurt@welkerhomes.com
    Moderator
    Owatonna, MN - Minnesota

    here are the winners of the best job site safety practices.

    I cant get the pps to load

    #162804
    theamcguy
    Pro
    Fayetteville, NC

    That’s a bummer 🙁

    Automotive Pro
    Fayetteville, NC

    #162809
    Anonymous
    Inactive

    Well?……C’mon C’mon C’mon 🙂

    #162844
    Nyx
    Pro
    Pittsburgh, PA

    seems to be lots of problems with posting the much anticipated content today 🙁

    #162939
    utopia78
    Pro
    Toronto, ON

    Now I’m curious and eager to see it? Bump

    Seriously – Safety First

    A Working Pro since 2004

    #162941
    Dustincoc
    Pro
    Madrid, NY

    C’mon man, 14 hours and you still haven’t got the pic up…

    Shop Blog: http://ravenbarsrepair.tumblr.com/
    Youtube Channel: https://www.youtube.com/channel/UCz498FKw9LF1awJsKIqhoxQ

    #162965
    jaydee
    Pro
    Spencer, Ma., happy 2015

    What a teaser .
    we’re waiting…..

    #163029

    I was hoping for sarcasm and some funny stuff. Please don’t disappoint.

    #163077
    DirtyWhiteBoy
    Pro
    Honolulu,, Hi.

    Safety is over rated.

    #163223
    Nyx
    Pro
    Pittsburgh, PA

    here is a little something to hold us over until they fix the problem.

    #163289
    jaydee
    Pro
    Spencer, Ma., happy 2015

    Not enough,
    We need MORE.
    25 feet up, on ladder jack.
    look next to the top tip.
    #16 to keep from sliding.
    these WERE NOT my guys, half azzed roofers

    #163292
    jaydee
    Pro
    Spencer, Ma., happy 2015

    maybe this will show the nail in fascia

    and boards with nails on ground to break the fall

    #163375
    utopia78
    Pro
    Toronto, ON

    The grinder with the tanks in the rat tail is just a classic! 🙂

    I hear stories of some of the young guys that I work with when I go to sites and they say their boss would tell them to tie the lifeline around their waste when on the balcony and that would be ok.

    A Working Pro since 2004

    #163534
    theamcguy
    Pro
    Fayetteville, NC

    here is a little something to hold us over until they fix the problem.

    Some scary stuff there. I remember working in a body shop. One of the guys there burnt down his old shop by welding near the gas tank and not being careful. Anyway at our shop he was welding and held the torch too close to the inlet filters for the paint room. The guy painting comes out all frazzled and smoking as the paint fumes caught on fire. Ruined the paint job. They took the torches away from the guy and if he needed to weld the boss did it.

    Automotive Pro
    Fayetteville, NC

    #163580
    Nyx
    Pro
    Pittsburgh, PA

    here is a little something to hold us over until they fix the problem.

    Some scary stuff there. I remember working in a body shop. One of the guys there burnt down his old shop by welding near the gas tank and not being careful. Anyway at our shop he was welding and held the torch too close to the inlet filters for the paint room. The guy painting comes out all frazzled and smoking as the paint fumes caught on fire. Ruined the paint job. They took the torches away from the guy and if he needed to weld the boss did it.

    somewhat comical since everyone ended up ok i guess. lol good story.

    #163631
    theamcguy
    Pro
    Fayetteville, NC

    Oh man we were rolling on the floor we were laughing so hard. Of course the painter was ticked off. Had to start prep all over again. Of course before that they used to put a 5 gallon bucket of water near where he was welding for a quick extinguisher. Yep you guessed it he set that on fire one day. Problem was he never paid attention to where he held his torch when he took it off the weld. You think the guy would of learned after he burnt down the old shop he worked at.

    Automotive Pro
    Fayetteville, NC

    #163994
    kurt@welkerhomes.com
    Moderator
    Owatonna, MN - Minnesota

    If there were a delete post option I would have, I was not able to get everything to load due to a problem on my end. Sorry.

    #164006
    theamcguy
    Pro
    Fayetteville, NC

    If there were a delete post option I would have, I was not able to get everything to load due to a problem on my end. Sorry.

    Yeah but we have had fun picking up where you left off.

    Automotive Pro
    Fayetteville, NC

    #164351
    utopia78
    Pro
    Toronto, ON

    If there were a delete post option I would have, I was not able to get everything to load due to a problem on my end. Sorry.

    Yeah but we have had fun picking up where you left off.

    Yeah we did! That’s a funny story Kurt! Guy sounds like a piece of work lol

    A Working Pro since 2004

    #164431
    RonW
    Moderator
    Holladay, Tn

    What the heck was this operator thinking?

    Ron

    A Working Pro since 1994!

    Member since March 26, 2014.

Viewing 20 posts - 1 through 20 (of 57 total)
  • You must be logged in to reply to this topic.
© Robert Bosch Tool Corporation 2014, all rights reserved.
queries. 1.959 seconds